Product code: ECK-KBT-006luxury steel door
Jakar Lattice-Textured Walnut Embossed Steel Door
Jakar fills a large rectangular panel at the centre of the leaf with a lattice of small squares, the steel equivalent of the square weave you see on a loom.
- Colour
- Ceviz
- Surface texture
- Kabartma
- Door leaf
- Single leaf
- Glazing
- No
You do not need to type the code, we see it when you arrive from the link. We send the measurement and the delivery time in writing.
On-site measurement
The frame opening and the swing direction are settled at your address.
Manufacture and installation
Manufacture to your measurement, removal of the old door and installation in one run.
Checked after installation
Lock and hinge adjustment are checked once the door is in.
What this model has
The texture stays inside the panel; the frame around it is left plain. The practical effect is that from a distance the door reads as a simple rectangle, and only up close does the weave come into view. It does not tire the eye the way a pattern covering the whole surface would.
The square weave has a second benefit in daily use: fine scratches that would show plainly on a flat surface tend to get lost inside the texture instead. On a busy apartment entrance that difference becomes visible after a few years.
The lattice has one limit: a deep scratch does not disappear into the texture, it stands out against it instead. We suggest covering the leaf during anything that risks that, like a house move, because touching up a deep mark is harder on this texture than on a flat surface.
- Walnut wood-tone surface
- Lattice-textured centre panel
- Framed rectangular field
- Vertical chrome bar handle
- Unglazed single leaf
- Marble threshold
Attributes
| Item | Value |
|---|---|
| Product code | ECK-KBT-006 |
| Colour | Ceviz |
| Surface texture | Kabartma |
| Door leaf | Single leaf |
| Glazing | No |
| Hardware | Bar kulp, Mermer eşik, Krom detay |
| Door frame inner size | 90 x 200 cm |
| Architrave outer size | 108 x 210 cm |
| Item | Value |
|---|---|
| Steel body | 2 mm Ereğli A1 steel |
| Insulation core | 150 kg/m³ rock wool |
| Lock system | Kale 256G, 14-point |
| Certification | TSE EN 1627 |
The values below are the same across every model in the catalogue. What separates the models is the surface design, the finish and the way the door leaf is built.
Every model carries a warranty as standard. On upper-tier models an extended warranty applies, depending on the material chosen.
Measurements
Inside the door frame (the door opening): 90 x 200 cm · Architrave edge (outside the door frame): 108 x 210 cm. If your door opening falls outside these measurements, the same model is made to your size.
Frequently asked about this model
What kind of door is the Jakar model?
Jakar sets a lattice of small squares into a large rectangular panel at the centre of the leaf, the steel equivalent of a woven loom pattern. The frame stays plain, so from a distance the door reads as a simple rectangle and the weave only shows up close.
Is Jakar made to the size of my own door opening?
Yes. Jakar is produced against your own opening rather than from a standard run, and the lattice-textured panel is re-framed within the new proportions so the weave still reads as centred on the leaf. Send the width and height measured inside the frame, and the team reconfirms them on site before fitting.
Which group does the Jakar door belong to?
Jakar sits in the luxury steel door group, on a walnut embossed surface finished with a framed lattice panel rather than an open relief. The body, insulation and lock hardware match the rest of the range; what sets this model apart is a texture that reads as woven cloth rather than carved stone.
Districts we install in
The catalogue is independent of area; for installation and service, move to the page for your own district.