Product code: ECK-LMK-016Laminoks steel door
Tanyeri Angled Timber Panel Laminoks Steel Door
Tanyeri cuts the walnut panel inside its black frame at an angle rather than square: both side edges of the panel lean the same way, so the leaf reads almost like a parallelogram.
- Colour
- Ahşap tonu
- Surface finish
- Laminoks
- Door leaf
- Single leaf
- Glazing
- No
You do not need to type the code, we see it when you arrive from the link. We send the measurement and the delivery time in writing.
On-site measurement
The frame opening and the swing direction are settled at your address.
Manufacture and installation
Manufacture to your measurement, removal of the old door and installation in one run.
Checked after installation
Lock and hinge adjustment are checked once the door is in.
What this model has
The handle leans at the same angle as the panel. Because the two angles line up, the whole composition points in a single direction; set at different angles, the leaf would look unresolved instead.
The angled edge changes nothing about how the door is fitted. The leaf is still a true rectangle; only the facing is cut at an angle. That question comes up often at survey, and the answer is straightforward: the frame and the opening stay a standard size.
The black frame contains the angled panel and reminds the eye of the leaf's true rectangular shape. Without a frame, the angle could make the whole door look askew.
Cutting the panel at an angle increases offcut, so this model takes a little longer to prepare than the square-cut ones. We state that clearly when the measurement is taken.
- Black frame
- Slanted-edge walnut panel
- Horizontal line texture
- Angled black bar handle
- Single leaf, unglazed
- Marble threshold
Attributes
| Item | Value |
|---|---|
| Product code | ECK-LMK-016 |
| Colour | Ahşap tonu |
| Surface finish | Laminoks |
| Door leaf | Single leaf |
| Glazing | No |
| Hardware | Bar kulp, Mermer eşik |
| Door frame inner size | 90 x 200 cm |
| Architrave outer size | 108 x 210 cm |
| Item | Value |
|---|---|
| Steel body | 2 mm Ereğli A1 steel |
| Insulation core | 150 kg/m³ rock wool |
| Lock system | Kale 256G, 14-point |
| Certification | TSE EN 1627 |
The values below are the same across every model in the catalogue. What separates the models is the surface design, the finish and the way the door leaf is built.
Every model carries a warranty as standard. On upper-tier models an extended warranty applies, depending on the material chosen.
Measurements
Inside the door frame (the door opening): 90 x 200 cm · Architrave edge (outside the door frame): 108 x 210 cm. If your door opening falls outside these measurements, the same model is made to your size.
Frequently asked about this model
What kind of door is the Tanyeri Angled Timber Panel Laminoks Steel Door?
Tanyeri cuts the walnut panel inside its black frame at an angle rather than square, so both side edges lean the same way and the leaf reads almost like a parallelogram. The handle is angled to match, which is what keeps the whole composition pointing in one direction instead of looking unresolved.
Can the Tanyeri Angled Timber Panel Laminoks Steel Door be made to measure?
Tanyeri leaves the workshop at a standard frame size as stock. For a different opening, the same black frame and slanted walnut panel carry over into a made-to-measure leaf; the frame and opening stay a standard rectangle regardless. Send the width and height from inside the frame, and allow a little extra time, since the angled cut takes longer to prepare.
Which group does the Tanyeri Angled Timber Panel Laminoks Steel Door belong to?
Tanyeri belongs to the Laminoks steel door group, in a timber tone with a single unglazed leaf and a bar handle. Body, insulation and lock hardware stay common across the group, and the facing layout is the real variable, so weigh it against the light your entrance gets.
Districts we install in
The catalogue is independent of area; for installation and service, move to the page for your own district.