Product code: ECK-SCP-008pressed sheet panel steel door
Bukle Quilted-Texture Pressed Sheet Panel Steel Door
Bukle presses a quilted texture into the centre panel of a grey leaf: squares set side by side, each slightly domed, the steel equivalent of an upholstered quilting stitch.
- Colour
- Gri
- Surface finish
- Sac panel
- Surface texture
- Kabartma
- Door leaf
- Single leaf
You do not need to type the code, we see it when you arrive from the link. We send the measurement and the delivery time in writing.
On-site measurement
The frame opening and the swing direction are settled at your address.
Manufacture and installation
Manufacture to your measurement, removal of the old door and installation in one run.
Checked after installation
Lock and hinge adjustment are checked once the door is in.
What this model has
The texture is confined to a framed area rather than spread across the whole leaf. With the surround left flat, the quilted section reads like a panel in its own right and the door doesn't turn busy. The grey tone keeps the shadow across the relief soft; the same texture in black would look considerably harsher.
The domed surfaces have a practical consequence: dust settles at the edges of the squares. A damp cloth clears it, but this surface asks for wiping down slightly more often than a flat leaf would.
The domed squares need some care during installation. Pressing against the texture while the leaf is being carried can leave a permanent mark, so our crew handles this model by its edges.
The depth of the texture can be reduced on request, though not flattened entirely; past a certain point the model stops looking like itself.
- Grey surface
- Quilted-texture relief panel
- Framed centre panel
- Vertical chrome bar handle
- Unglazed single leaf
- Marble threshold
Attributes
| Item | Value |
|---|---|
| Product code | ECK-SCP-008 |
| Colour | Gri |
| Surface finish | Sac panel |
| Surface texture | Kabartma |
| Door leaf | Single leaf |
| Glazing | No |
| Hardware | Bar kulp, Mermer eşik, Krom detay |
| Door frame inner size | 90 x 200 cm |
| Architrave outer size | 108 x 210 cm |
| Item | Value |
|---|---|
| Steel body | 2 mm Ereğli A1 steel |
| Insulation core | 150 kg/m³ rock wool |
| Lock system | Kale 256G, 14-point |
| Certification | TSE EN 1627 |
The values below are the same across every model in the catalogue. What separates the models is the surface design, the finish and the way the door leaf is built.
Every model carries a warranty as standard. On upper-tier models an extended warranty applies, depending on the material chosen.
Measurements
Inside the door frame (the door opening): 90 x 200 cm · Architrave edge (outside the door frame): 108 x 210 cm. If your door opening falls outside these measurements, the same model is made to your size.
Frequently asked about this model
What is the quilted texture on Bukle meant to resemble?
It's the steel equivalent of an upholstered quilting stitch: squares set side by side, each slightly domed, pressed into a framed area at the centre of the leaf. The surround is left flat, so the quilted section reads as its own panel rather than spreading across the whole door.
Can Bukle be built to a non-standard opening?
Yes. The quilted panel at the centre is re-framed within the surrounding flat surface to suit your own door opening, rather than stretched out of its square proportions. Measure the opening from inside the frame and we check it again on site before manufacture, since carrying the leaf by its textured face risks marking it.
Can the depth of the quilting on Bukle be reduced?
Yes, to a point. We can press the texture shallower on request, but it isn't flattened completely; take the depth down too far and the pattern stops reading as quilting at all, which would mean losing what makes this particular model recognisable.
Districts we install in
The catalogue is independent of area; for installation and service, move to the page for your own district.