Skip to content
Esma Çelik Kapı

Product code: ECK-SCP-010pressed sheet panel steel door

Münhani Spiral-Relief Pressed Sheet Panel Steel Door

Münhani sets a circular spiral relief at the centre of the panel, with a diamond-textured fill running around it; together the two give the surface a slow, wave-like feel.

Colour
Gri
Surface finish
Sac panel
Surface texture
Kabartma
Hardware
Bar kulp, Mermer eşik, Krom detay

You do not need to type the code, we see it when you arrive from the link. We send the measurement and the delivery time in writing.

Grey pressed sheet panel steel door: circular spiral relief, diamond-textured fill
  • Door from the Münhani Spiral-Relief Pressed Sheet Panel Steel Door series

    On-site measurement

    The frame opening and the swing direction are settled at your address.

  • Villa door, how the Münhani Spiral-Relief Pressed Sheet Panel Steel Door series looks

    Manufacture and installation

    Manufacture to your measurement, removal of the old door and installation in one run.

  • Anthracite door from the Münhani Spiral-Relief Pressed Sheet Panel Steel Door series

    Checked after installation

    Lock and hinge adjustment are checked once the door is in.

What this model has

The centre of the spiral isn't placed at the exact middle of the leaf; it sits slightly lower. That's down to eye line: someone looking at the closed door from a standing position sees the pattern as centred, even though it technically isn't.

The grey surface lets the turn of the spiral be followed through soft shadow rather than contrast, so the pattern doesn't shout for attention. The leaf is unglazed and made from a single panel, and the vertical chrome handle sits to the left of the spiral.

The framed centre panel follows the same layout as Bukle elsewhere in the range; what differs is the texture inside that panel, not the leaf's overall proportions.

The spiral's centre point shifts with the height of the leaf, moving a little lower on a taller opening to stay at the standing eye line. Keep it at one fixed position regardless of height, and on a tall door the pattern would end up sitting too high; that adjustment is one of the visible benefits of building to measure.

  • Grey surface
  • Circular spiral relief at the centre
  • Diamond-textured fill around it
  • Framed centre panel
  • Vertical chrome bar handle
  • Marble threshold

Attributes

Münhani Spiral-Relief Pressed Sheet Panel Steel Door technical details
ItemValue
Product codeECK-SCP-010
ColourGri
Surface finishSac panel
Surface textureKabartma
HardwareBar kulp, Mermer eşik, Krom detay
Door frame inner size90 x 200 cm
Architrave outer size108 x 210 cm
Standard on every model
ItemValue
Steel body2 mm Ereğli A1 steel
Insulation core150 kg/m³ rock wool
Lock systemKale 256G, 14-point
CertificationTSE EN 1627

The values below are the same across every model in the catalogue. What separates the models is the surface design, the finish and the way the door leaf is built.

Every model carries a warranty as standard. On upper-tier models an extended warranty applies, depending on the material chosen.

Measurements

Inside the door frame (the door opening): 90 x 200 cm · Architrave edge (outside the door frame): 108 x 210 cm. If your door opening falls outside these measurements, the same model is made to your size.

Frequently asked about this model

Why isn't the spiral on Münhani placed at the exact centre of the leaf?

It sits slightly lower than the geometric middle, because someone standing in front of the closed door and looking at it naturally sees the pattern as centred from that eye line, even though it technically isn't. Placed at the true centre, the spiral would look a little high instead.

Can the spiral position on Münhani be adjusted for my opening?

Yes. Münhani is produced against your own door opening, and the spiral is repositioned slightly below centre so it still sits at standing eye level whatever height the leaf ends up. Send the opening measured from inside the frame; we confirm it again on site, and that adjustment is worked out once we have it.

Does the spiral position change on a taller door?

Yes. On a taller opening the centre of the spiral is moved a little lower so it still sits at standing eye level; left at one fixed position regardless of height, the pattern would end up looking too high on a tall leaf. That adjustment is worked out once we have your measurement.

Last updated

The date is the last change date of the content files behind this page; it does not move forward each time the page opens.

Call nowAsk on WhatsApp
Münhani Spiral-Relief Pressed Sheet Panel Steel Door — ECK-SCP-010 — Esma Çelik Kapı