Product code: ECK-PVC-016PVC embossed steel door
Agat Diamond-Embossed Anthracite PVC Steel Door
Agat sets a single large diamond relief at the centre of an anthracite surface and draws angled lines out from its corners toward the edges of the leaf.
- Colour
- Antrasit
- Surface finish
- PVC
- Surface texture
- Kabartma
- Door leaf
- Single leaf
You do not need to type the code, we see it when you arrive from the link. We send the measurement and the delivery time in writing.
On-site measurement
The frame opening and the swing direction are settled at your address.
Manufacture and installation
Manufacture to your measurement, removal of the old door and installation in one run.
Checked after installation
Lock and hinge adjustment are checked once the door is in.
What this model has
A centred pattern like this is rare in the group. Most models divide the surface or work it as a texture; here there is one focal point and the whole composition answers to it. The eye goes to the middle first, then follows the lines outward.
A second, smaller diamond sits inside the first. Two nested shapes read as more depth than a single outline could manage on its own.
The chrome handle stays off to the side, clear of the pattern. Placed inside a centred composition like this one, a handle would split the focal point in two.
The difference in depth between the outer and inner diamond is set in the die. The outer line is cut shallow and the inner one deep; if both sat at the same depth, the sense of volume would flatten out.
- Anthracite PVC facing
- Large diamond relief at the centre
- Angled lines radiating outward
- Chrome vertical bar handle
- Unglazed single leaf
- Marble threshold
Attributes
| Item | Value |
|---|---|
| Product code | ECK-PVC-016 |
| Colour | Antrasit |
| Surface finish | PVC |
| Surface texture | Kabartma |
| Door leaf | Single leaf |
| Glazing | No |
| Hardware | Bar kulp, Mermer eşik, Krom detay |
| Door frame inner size | 90 x 200 cm |
| Architrave outer size | 108 x 210 cm |
| Item | Value |
|---|---|
| Steel body | 2 mm Ereğli A1 steel |
| Insulation core | 150 kg/m³ rock wool |
| Lock system | Kale 256G, 14-point |
| Certification | TSE EN 1627 |
The values below are the same across every model in the catalogue. What separates the models is the surface design, the finish and the way the door leaf is built.
Every model carries a warranty as standard. On upper-tier models an extended warranty applies, depending on the material chosen.
Measurements
Inside the door frame (the door opening): 90 x 200 cm · Architrave edge (outside the door frame): 108 x 210 cm. If your door opening falls outside these measurements, the same model is made to your size.
Frequently asked about this model
What does the Agat Diamond-Embossed Anthracite PVC Steel Door look like?
Agat sets a single large diamond relief at the centre of an anthracite surface and draws angled lines out from its corners toward the leaf's edges. A centred pattern like this is rare in the group: most models divide or texture the surface, while here the whole composition answers to one focal point.
Can the Agat door be made to a non-standard opening?
Yes. The leaf and frame are worked out from your own door opening and the diamond pattern is re-proportioned to that size rather than simply stretched, since a pattern built around one centre loses its balance if the width changes without the layout changing to match. We draw the new layout, check the opening again on site, and send it for approval before manufacture starts.
Which group does the Agat door belong to?
Agat belongs to the PVC-embossed steel door group and carries an anthracite surface, a PVC facing and an unglazed single leaf. Body, insulation and lock stay the same across the group; what changes is the surface pattern, and here that means a centred diamond rather than the banding seen elsewhere in the range.
Districts we install in
The catalogue is independent of area; for installation and service, move to the page for your own district.